Journal Description
Materials
Materials
is an international peer-reviewed, open access journal on materials science and engineering published semimonthly online by MDPI. The Portuguese Materials Society (SPM), Spanish Materials Society (SOCIEMAT) and Manufacturing Engineering Society (MES) are affiliated with Materials and their members receive discounts on the article processing charges.
- Open Access— free for readers, with article processing charges (APC) paid by authors or their institutions.
- High Visibility: indexed within Scopus, SCIE (Web of Science), PubMed, PMC, Ei Compendex, CaPlus / SciFinder, Inspec, Astrophysics Data System, and other databases.
- Journal Rank: JCR - Q2 (Metallurgy & Metallurgical Engineering) / CiteScore - Q2 (Condensed Matter Physics)
- Rapid Publication: manuscripts are peer-reviewed and a first decision is provided to authors approximately 13.9 days after submission; acceptance to publication is undertaken in 2.7 days (median values for papers published in this journal in the second half of 2023).
- Recognition of Reviewers: reviewers who provide timely, thorough peer-review reports receive vouchers entitling them to a discount on the APC of their next publication in any MDPI journal, in appreciation of the work done.
- Testimonials: See what our editors and authors say about Materials.
- Companion journals for Materials include: Electronic Materials and Construction Materials.
Impact Factor:
3.4 (2022);
5-Year Impact Factor:
3.8 (2022)
Latest Articles
Investigation of Mechanical Properties of Polymer-Infiltrated Tetrapodal Zinc Oxide in Different Variants
Materials 2024, 17(9), 2112; https://doi.org/10.3390/ma17092112 (registering DOI) - 29 Apr 2024
Abstract
The aim of this study was to evaluate the influence of weight ratio, the shape of the precursor particles, and the application of a phosphate-monomer-containing primer on the mechanical properties of polymer infiltrated ceramic networks (PICNs) using zinc oxide. Two different types of
[...] Read more.
The aim of this study was to evaluate the influence of weight ratio, the shape of the precursor particles, and the application of a phosphate-monomer-containing primer on the mechanical properties of polymer infiltrated ceramic networks (PICNs) using zinc oxide. Two different types of zinc oxide particles were used as precursors to produce zinc oxide networks by sintering, each with two different densities resulting in two different weight ratios of the PICNs. For each of these different networks, two subgroups were built: one involving the application of a phosphate-monomer-containing primer prior to the infiltration of Bis-GMA/TEGDMA and one without. Elastic modulus and flexural strength were determined by using the three-point bending test. Vertical substance loss determined by the chewing simulation was evaluated with a laser scanning microscope. There was a statistically significant influence of the type of precursor particles on the flexural strength and in some cases on the elastic modulus. The application of a primer lead to a significant increase in the flexural strength and in most cases also in the elastic modulus. A higher weight ratio of zinc oxide led to a significantly higher elastic modulus. Few statistically significant differences were found for the vertical substance loss. By varying the shape of the particles and the weight fraction of zinc oxide, the mechanical properties of the investigated PICN can be controlled. The use of a phosphate-monomer-containing primer strengthens the bond between the infiltrated polymer and the zinc oxide, thus increasing the strength of the composite.
Full article
(This article belongs to the Special Issue Polymer Composites: Microstructural, Thermal and Mechanical Properties (Second Volume))
Open AccessArticle
Iron–Carbon Nanospheres as Promising Material for Magnetic Assisted Adsorption and Separation of Impurities from a Liquid Phase
by
Iwona Pełech, Sabina Lewinska, Monika Arciszewska, Abdul Khaliq, Anna Ślawska-Waniewska, Daniel Sibera, Piotr Staciwa and Urszula Narkiewicz
Materials 2024, 17(9), 2111; https://doi.org/10.3390/ma17092111 (registering DOI) - 29 Apr 2024
Abstract
The composites containing various iron compounds and highly microporous carbon spheres were produced and investigated for structural and magnetic properties. Iron citrate, nitrate and chloride were used to prepare samples and the obtained products contained iron, iron carbide or magnetite. All the produced
[...] Read more.
The composites containing various iron compounds and highly microporous carbon spheres were produced and investigated for structural and magnetic properties. Iron citrate, nitrate and chloride were used to prepare samples and the obtained products contained iron, iron carbide or magnetite. All the produced samples were characterized by high porosity and good magnetic properties. The coupling of the high porosity of carbon spheres with magnetic properties of iron compounds provides a potential application of the composites to removal of impurities from water, followed by a magnetic separation of the sorbent.
Full article
(This article belongs to the Special Issue Adsorption Materials and Their Applications)
Open AccessArticle
Microstructural Evolution and Failure in Fibrous Network Materials: Failure Mode Transition from the Competition between Bond and Fiber
by
Yao Zhang, Weihua Wang, Pengfei Wang, Zixing Lu and Zhenyu Yang
Materials 2024, 17(9), 2110; https://doi.org/10.3390/ma17092110 (registering DOI) - 29 Apr 2024
Abstract
For the complex structure of fibrous network materials, it is a challenge to analyze the network strength and deformation mechanism. Here, we identify a failure mode transition within the network material comprising brittle fibers and bonds, which is related to the strength ratio
[...] Read more.
For the complex structure of fibrous network materials, it is a challenge to analyze the network strength and deformation mechanism. Here, we identify a failure mode transition within the network material comprising brittle fibers and bonds, which is related to the strength ratio of the bond to the fiber. A failure criterion for this type of fibrous network is proposed to quantitatively characterize this transition between bond damage and fiber damage. Additionally, tensile experiments on carbon and ceramic fibrous network materials were conducted, and the experimental results show that the failure modes of these network materials satisfy the theoretical prediction. The relationship between the failure mode, the relative density of network and strength of the components is established based on finite element analysis of the 3D network model. The failure mode transforms from bond damage to fiber damage as increasing of bond strength. According to the transition of the failure modes in the brittle fibrous network, it is possible to tailor the mechanical properties of fibrous network material by balancing the competition between bond and fiber properties, which is significant for optimizing material design and engineering applications.
Full article
Open AccessArticle
Effect of Welding Parameters on Al/Mg Dissimilar Friction Stir Lap Welding with and without Ultrasonic Vibration
by
Junjie Zhao, Bo Zhao, Chuansong Wu and Najib Ahmad Muhammad
Materials 2024, 17(9), 2109; https://doi.org/10.3390/ma17092109 (registering DOI) - 29 Apr 2024
Abstract
The amount of heat input during welding impacts the weld’s thermal and mechanical behavior and the joint’s properties. The current study involved conducting AA 6061 and AZ31B Mg dissimilar welding, using friction stir lap welding (FSLW) and ultrasonic vibration-enhanced FSLW (UVeFSLW). The comparison
[...] Read more.
The amount of heat input during welding impacts the weld’s thermal and mechanical behavior and the joint’s properties. The current study involved conducting AA 6061 and AZ31B Mg dissimilar welding, using friction stir lap welding (FSLW) and ultrasonic vibration-enhanced FSLW (UVeFSLW). The comparison and analysis of the welding load, the weld’s macro-microstructure, intermetallic compounds (IMCs), and joint properties were conducted by adjusting the process parameters. The study also examined the effect of ultrasonic vibration (UV) variations on welding heat input. The study demonstrated that it is possible to reduce the welding load by employing UV. Moreover, this impact becomes more pronounced as the welding heat input decreases. Additionally, the material flow in the weld, the width of the weld nugget zone, and the continuous IMC layer are significantly influenced by ultrasonic vibration, irrespective of the heat input during welding. However, the impact on large areas of irregular IMCs or eutectic structures is relatively small. Furthermore, achieving better joint properties becomes more feasible when a higher welding speed is employed for the Al alloy placed on top. Specifically, the impact of UV becomes more evident at higher welding speeds (≥220 mm/min).
Full article
(This article belongs to the Topic Development of Friction Stir Welding and Processing)
Open AccessArticle
Machine Learning-Based Simulation of the Air Conditioner Operating Time in Concrete Structures with Bayesian Thresholding
by
Changhwan Jang, Hong-Gi Kim and Byeong-Hun Woo
Materials 2024, 17(9), 2108; https://doi.org/10.3390/ma17092108 (registering DOI) - 29 Apr 2024
Abstract
Efficient energy use is crucial for achieving carbon neutrality and reduction. As part of these efforts, research is being carried out to apply a phase change material (PCM) to a concrete structure together with an aggregate. In this study, an energy consumption simulation
[...] Read more.
Efficient energy use is crucial for achieving carbon neutrality and reduction. As part of these efforts, research is being carried out to apply a phase change material (PCM) to a concrete structure together with an aggregate. In this study, an energy consumption simulation was performed using data from concrete mock-up structures. To perform the simulation, the threshold investigation was performed through the Bayesian approach. Furthermore, the spiking part of the spiking neural network was modularized and integrated into a recurrent neural network (RNN) to find accurate energy consumption. From the training-test results of the trained neural network, it was possible to predict data with an R2 value of 0.95 or higher through data prediction with high accuracy for the RNN. In addition, the spiked parts were obtained; it was found that PCM-containing concrete could consume 32% less energy than normal concrete. This result suggests that the use of PCM can be a key to reducing the energy consumption of concrete structures. Furthermore, the approach of this study is considered to be easily applicable in energy-related institutions and the like for predicting energy consumption during the summer.
Full article
(This article belongs to the Special Issue State-of-the-Art Construction Materials and Technologies for Structural Health Monitoring of Infrastructures)
►▼
Show Figures
Figure 1
Open AccessCommunication
Load-Independent Hardness and Indentation Size Effect in Iron Aluminides
by
Sebastian Balos, Milan Pecanac, Mirjana Trivkovic, Savo Bojic and Pavel Hanus
Materials 2024, 17(9), 2107; https://doi.org/10.3390/ma17092107 (registering DOI) - 29 Apr 2024
Abstract
In this paper, an iron–aluminide intermetallic compound with cerium addition was subjected to Vickers microhardness testing. A full range of Vickers microhardness loadings was applied: 10, 25, 50, 100, 200, 300, 500, and 1000 g. Tests were conducted in two areas: 0.5 mm
[...] Read more.
In this paper, an iron–aluminide intermetallic compound with cerium addition was subjected to Vickers microhardness testing. A full range of Vickers microhardness loadings was applied: 10, 25, 50, 100, 200, 300, 500, and 1000 g. Tests were conducted in two areas: 0.5 mm under the surface of the rolled specimen and in the center. The aim was to find the optimal loading range that gives the true material microhardness, also deemed load-independent hardness, HLIH. The results suggest that in the surface area, the reverse indentation size effect (RISE) occurred, similar to ceramics and brittle materials, while in the center, indentation size effect (ISE) behavior was obtained, more similar to metals. This clearly indicated an optimal microhardness of over 500 g in the surface region and over 100 g in the central region of the specimen. Load dependencies were quantitatively described by Meyer’s law, proportional specimen resistance (PSR), and the modified PSR model. The modified PSR model proved to be the most adequate.
Full article
(This article belongs to the Special Issue Intermetallics: From Design to Structural and Properties)
Open AccessArticle
Quasi-In Situ Observation of the Microstructural Response during Fatigue Crack Growth of Friction Stir Welded AA2024-T4 Joint
by
Jun Yang, Xianmin Chen, Huaxia Zhao, Jihong Dong and Feng Jin
Materials 2024, 17(9), 2106; https://doi.org/10.3390/ma17092106 - 29 Apr 2024
Abstract
The reliability of friction stir welded joints is a critical concern, particularly given their potential applications in the aerospace manufacturing industry. This study offers a quasi-in situ observation of the microstructural response during fatigue crack growth (FCG) of a friction stir welded AA2024-T4
[...] Read more.
The reliability of friction stir welded joints is a critical concern, particularly given their potential applications in the aerospace manufacturing industry. This study offers a quasi-in situ observation of the microstructural response during fatigue crack growth (FCG) of a friction stir welded AA2024-T4 joint, aiming to correlate fatigue crack growth behavior with mechanical properties investigated using electron backscatter diffraction (EBSD). Notched compact tension (CT) specimens corresponding to the morphology of the stir zone (SZ), advancing side (AS), and retreating side (RS) were meticulously designed. The findings indicate that the welding process enhances the joint’s resistance to fatigue crack growth, with the base metal exhibiting a shorter fatigue life (i.e., ~105 cycles) compared to the welding zones (SZ ~ 3.5 × 105 cycles, AS ~ 2.5 × 105 cycles, and RS ~ 3.0 × 105 cycles). Crack propagation occurs within the stir zone, traversing refined grains, which primarily contribute to the highest fatigue life and lowest FCG rate. Additionally, cracks initiate in AS and RS, subsequently expanding into the base metal. Moreover, the study reveals a significant release of residual strain at the joint, particularly notable in the Structural-CT-RS (Str-CT-RS) sample compared to the Str-CT-AS sample during the FCG process. Consequently, the FCG rate of Str-CT-AS is higher than that of Str-CT-RS. These findings have significant implications for improving the reliability and performance of aerospace components.
Full article
(This article belongs to the Special Issue Advances in Solid-State Welding Processes)
Open AccessArticle
Synthesis of MPEG-b-PLLA Diblock Copolymers and Their Crystallization Performance with PDLA and PLLA Composite Films
by
Wenjing Wu, Weixin Wu, Mingwei Guo, Ruizhe Wang, Xuanxuan Wang and Qinwei Gao
Materials 2024, 17(9), 2105; https://doi.org/10.3390/ma17092105 - 29 Apr 2024
Abstract
Methoxy poly(ethylene glycol)-block-poly(L-lactide) (MPEG-b-PLLA) has a wide range of applications in pharmaceuticals and biology, and its structure and morphology have been thoroughly studied. In the experiment, we synthesized MPEG-b-PLLA with different block lengths using the principle of ring-opening polymerization by controlling the amount
[...] Read more.
Methoxy poly(ethylene glycol)-block-poly(L-lactide) (MPEG-b-PLLA) has a wide range of applications in pharmaceuticals and biology, and its structure and morphology have been thoroughly studied. In the experiment, we synthesized MPEG-b-PLLA with different block lengths using the principle of ring-opening polymerization by controlling the amount of lactic acid added. The thermodynamic properties of copolymers and the crystallization properties of blends were studied separately. The crystallization kinetics of PDLA/MPEG-b-PLA and PLLA/MPEG-b-PLA composite films were studied using differential scanning calorimetry (DSC). The results indicate that the crystallization kinetics of composite films are closely related to the amount of block addition. The crystallinity of the sample first increases and then decreases with an increase in MPEG-b-PLLA content. These results were also confirmed in polarized optical microscope (POM) and wide-angle X-ray diffraction (WAXD) tests. When 3% MPEG-b-PLLA was added to the PDLA matrix, the blend exhibited the strongest crystallization performance.
Full article
Open AccessReview
Progress and Challenges of Additive Manufacturing of Tungsten and Alloys as Plasma-Facing Materials
by
Logan Howard, Gabriel D. Parker and Xiao-Ying Yu
Materials 2024, 17(9), 2104; https://doi.org/10.3390/ma17092104 - 29 Apr 2024
Abstract
Tungsten (W) and W alloys are considered as primary candidates for plasma-facing components (PFCs) that must perform in severe environments in terms of temperature, neutron fluxes, plasma effects, and irradiation bombardment. These materials are notoriously difficult to produce using additive manufacturing (AM) methods
[...] Read more.
Tungsten (W) and W alloys are considered as primary candidates for plasma-facing components (PFCs) that must perform in severe environments in terms of temperature, neutron fluxes, plasma effects, and irradiation bombardment. These materials are notoriously difficult to produce using additive manufacturing (AM) methods due to issues inherent to these techniques. The progress on applying AM techniques to W-based PFC applications is reviewed and the technical issues in selected manufacturing methods are discussed in this review. Specifically, we focus on the recent development and applications of laser powder bed fusion (LPBF), electron beam melting (EBM), and direct energy deposition (DED) in W materials due to their abilities to preserve the properties of W as potential PFCs. Additionally, the existing literature on irradiation effects on W and W alloys is surveyed, with possible solutions to those issues therein addressed. Finally, the gaps in possible future research on additively manufactured W are identified and outlined.
Full article
(This article belongs to the Special Issue Materials, Processing, and Post-treatment for Metal-Based Additive Manufacturing)
Open AccessArticle
Catalytic Oxidation of Chlorobenzene over Amorphous Manganese-Chromium Catalysts Supported by UiO-66-Derived ZrOx
by
Pengfei Zhu, Qiaosen Yuan, Na Li, Zhaoxia Hu and Shouwen Chen
Materials 2024, 17(9), 2103; https://doi.org/10.3390/ma17092103 - 29 Apr 2024
Abstract
The development of efficient catalysts with longevity to remove chlorobenzene is challenging due to Cl poisoning. Herein, a series of Mn-Cr/ZrOx catalysts supported by Zr-based metal-organic framework (UiO-66)-derived ZrOx was prepared and investigated for chlorobenzene (CB) catalytic oxidation. MnCr/ZrOx-M
[...] Read more.
The development of efficient catalysts with longevity to remove chlorobenzene is challenging due to Cl poisoning. Herein, a series of Mn-Cr/ZrOx catalysts supported by Zr-based metal-organic framework (UiO-66)-derived ZrOx was prepared and investigated for chlorobenzene (CB) catalytic oxidation. MnCr/ZrOx-M prepared via a wet impregnation method presented an amorphous structure, indicating the homogeneous dispersion of Cr and Mn, which improved acid and redox properties. 40Mn7Cr3/ZrOx-M exhibited the best catalytic activity for chlorobenzene oxidation with T90 of 293 ℃, which is mainly due to the strong interaction between manganese and chromium promoted by the large specific surface area of the ZrOx support. Furthermore, 40Mn7Cr3/ZrOx-M presented excellent stability for chlorobenzene oxidation.
Full article
Open AccessArticle
Effect of Recycled Fine Aggregates on the Mechanical and Drying Shrinkage Properties of Alkali-Activated Recycled Concrete
by
Ling Luo, Wu Yao and Gang Liao
Materials 2024, 17(9), 2102; https://doi.org/10.3390/ma17092102 - 29 Apr 2024
Abstract
In this paper, the workability, mechanical, ion leaching, and drying shrinkage properties of alkali-activated concrete with recycled coarse and fine aggregates were studied, and the pore structure and micro-morphology of different alkali-activated recycled aggregate concretes (AARACs) were characterized by using the mercury intrusion
[...] Read more.
In this paper, the workability, mechanical, ion leaching, and drying shrinkage properties of alkali-activated concrete with recycled coarse and fine aggregates were studied, and the pore structure and micro-morphology of different alkali-activated recycled aggregate concretes (AARACs) were characterized by using the mercury intrusion method and scanning electron microscopy, respectively. The experimental results showed that with the increase in the replacement rate of the recycled fine aggregate (RFA), the flowability showed a decreasing trend. Adding a certain amount of RFA improves the mechanical properties of the AARAC. The compressive strength at a curing age of 28 days was 65.3 MPa with 70 wt% RFA replacement. When the replacement rate of the RFA was 100 wt%, the maximum splitting tensile strength (4.5 MPa) was obtained at a curing age of 7 days. However, the addition of the RFA had little effect on the flexural strength of the AARAC. As an extension of the curing age, the splitting tensile strength, flexural strength, tension-to-compression ratio, and flexure-to-compression ratio all showed an increasing trend at first and then a decreasing trend. At a curing age of 7 days, the tension-to-compression ratio and flexure-to-compression ratio were both high (except for those of R100), indicating that the ductility and toughness of the specimen were improved. The addition of the RFA increased the drying shrinkage of the AARAC. At a curing age of 120 days, compared to the specimen without the RFA, the drying shrinkage rate of the specimen with the addition of 70 wt% RFA increased by 34.15%. As the curing age increased, the microstructure of the reaction products became denser, but the proportion of large-diameter pores increased. This study evaluated the application of RFA in AARAC. The experimental results showed that the RFA-based AARAC had acceptable mechanical and durability properties.
Full article
(This article belongs to the Special Issue Advances in Concrete and Binders for Sustainable Engineering)
Open AccessArticle
Assessment of Changes in Abrasive Wear Resistance of a Welded Joint of Low-Alloy Martensitic Steel Using Microabrasion Test
by
Krzysztof Ligier, Jerzy Napiórkowski and Magdalena Lemecha
Materials 2024, 17(9), 2101; https://doi.org/10.3390/ma17092101 - 29 Apr 2024
Abstract
Martensitic low-alloy steels are widely used in machine construction. Due to their declared weldability, arc welding is most often used to join elements made of this type of steel. However, the high temperature associated with welding causes unfavourable changes in the microstructure, resulting
[...] Read more.
Martensitic low-alloy steels are widely used in machine construction. Due to their declared weldability, arc welding is most often used to join elements made of this type of steel. However, the high temperature associated with welding causes unfavourable changes in the microstructure, resulting in reduced abrasion resistance. Therefore, it is important to know the tribological properties of the welded joint. This article presents the results of a study on the abrasion wear resistance of a welded joint of an abrasion-resistant steel. This study tested a welded joint of an abrasive-resistant steel produced by the arc welding method. Wear testing of the welded joint was carried out under laboratory conditions by the ball-cratering method in the presence of abrasive slurry on the cross-section of the welded joint. Based on the test results, the change in the abrasive wear rate of the material as a function of the distance from the welded joint axis was determined. It was also found that the thermal processes accompanying welding caused structural changes that increased the wear rate index value. Adverse changes in the tribological properties of a welded material persist up to a distance of approx. 20 mm from the weld centre.
Full article
(This article belongs to the Special Issue Welding, Joining and Additive Manufacturing: Experiments, Materials and Modelling)
Open AccessReview
The Contribution of Scanning Force Microscopy on Dental Research: A Narrative Review
by
Christine Müller-Renno and Christiane Ziegler
Materials 2024, 17(9), 2100; https://doi.org/10.3390/ma17092100 - 29 Apr 2024
Abstract
Scanning force microscopy (SFM) is one of the most widely used techniques in biomaterials research. In addition to imaging the materials of interest, SFM enables the mapping of mechanical properties and biological responses with sub-nanometer resolution and piconewton sensitivity. This review aims to
[...] Read more.
Scanning force microscopy (SFM) is one of the most widely used techniques in biomaterials research. In addition to imaging the materials of interest, SFM enables the mapping of mechanical properties and biological responses with sub-nanometer resolution and piconewton sensitivity. This review aims to give an overview of using the scanning force microscope (SFM) for investigations on dental materials. In particular, SFM-derived methods such as force–distance curves (scanning force spectroscopy), lateral force spectroscopy, and applications of the FluidFM® will be presented. In addition to the properties of dental materials, this paper reports the development of the pellicle by the interaction of biopolymers such as proteins and polysaccharides, as well as the interaction of bacteria with dental materials.
Full article
(This article belongs to the Special Issue Materials and Techniques in Dentistry, Oral Surgery and Orthodontics)
Open AccessArticle
Study on Dynamic Mechanical Properties of Sandwich Beam with Stepwise Gradient Polymethacrylimide (PMI) Foam Core under Low-Velocity Impact
by
Mousab Mahgoub, Cong Liu and Zhuhua Tan
Materials 2024, 17(9), 2099; https://doi.org/10.3390/ma17092099 - 29 Apr 2024
Abstract
Different PMI foam materials of 52, 110, and 200 kg/m3 were used to design stepwise gradient cores to improve the impact resistance of the sandwich beam. The stepwise gradient core consists of three layers arranged in positive gradient, negative gradient, and sandwich-core
[...] Read more.
Different PMI foam materials of 52, 110, and 200 kg/m3 were used to design stepwise gradient cores to improve the impact resistance of the sandwich beam. The stepwise gradient core consists of three layers arranged in positive gradient, negative gradient, and sandwich-core (e.g., 200/52/200). These sandwich beams were subjected to the impact of a steel projectile under impact momentum of 10 to 20 kg·m/s, corresponding to impact energy in the range of 12.5 to 50 J. During the test, the impact force was recorded by an accelerometer, and the different failure modes were also obtained. Subsequently, the influence of the layer arrangement on the energy absorption and load transfer mechanism between the different layers was analyzed. The results showed that the top layer with a large density can improve the impact force, but the middle/bottom layer with a low density promoted specific energy absorption. Thus, based on these two points, the negative gradient core (200/110/52) had an excellent specific energy absorption because it can transfer and expand the area to bear the load layer by layer, which improved the energy absorption in each layer. Combined with the failure modes, the load transfer and deformation mechanisms between the layers were also discussed. The present work provided a valuable method to design an efficient lightweight sandwich structure in the protection field.
Full article
(This article belongs to the Special Issue Dynamic Behavior of Advanced Materials and Structures)
Open AccessArticle
All-Silicon Polarization-Insensitive Metamaterial Absorber in the Terahertz Range
by
Zongcheng Xu, Yujie Li, Bin Han, Yue Wang, Quan Yuan, Yanan Li, Weiyan He, Junhua Hao, Liang Wu and Jianquan Yao
Materials 2024, 17(9), 2098; https://doi.org/10.3390/ma17092098 - 29 Apr 2024
Abstract
All-silicon terahertz absorbers have attracted considerable interest. We present a design and numerical study of an all-silicon polarization-insensitive terahertz metamaterial absorber. The meta-atoms of the metamaterial absorber are square silicon rings which can be viewed as gratings. By properly optimizing the structure of
[...] Read more.
All-silicon terahertz absorbers have attracted considerable interest. We present a design and numerical study of an all-silicon polarization-insensitive terahertz metamaterial absorber. The meta-atoms of the metamaterial absorber are square silicon rings which can be viewed as gratings. By properly optimizing the structure of the meta-atom, we achieve a broadband absorptivity that is above 90% ranging from 0.77 THz to 2.53 THz, with a relative bandwidth of 106.7%. Impedance matching reduces the reflection of the terahertz waves and the (0, ±1)-order diffraction induce the strong absorption. The absorption of this absorber is insensitive to the polarization of the terahertz wave and has a large incident angle tolerance of up to 60 degrees. The all-silicon metamaterial absorber proposed here provides an effective way to obtain broadband absorption in the terahertz regime. Metamaterial absorbers have outstanding applications in terahertz communication and imaging.
Full article
Open AccessArticle
Effect of Laser Scan Speed on Defects and Texture Development of Pure Chromium Metal Fabricated via Powder Bed Fusion-Laser Beam
by
Yong Seong Kim, Ozkan Gokcekaya, Aira Matsugaki and Takayoshi Nakano
Materials 2024, 17(9), 2097; https://doi.org/10.3390/ma17092097 - 29 Apr 2024
Abstract
Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as a high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by its high ductile–brittle transition temperature (DBTT). Recently,
[...] Read more.
Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as a high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by its high ductile–brittle transition temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explored the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of a <100> cubic texture. Consequently, a reduction in high-angle grain boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.
Full article
(This article belongs to the Special Issue Advances in Materials Joining and Additive Manufacturing)
Open AccessArticle
Performance of High-Dose Reclaimed Asphalt Mixtures (RAPs) in Hot In-Place Recycling Based on Balanced Design
by
Lei Jiang, Junan Shen and Wei Wang
Materials 2024, 17(9), 2096; https://doi.org/10.3390/ma17092096 - 29 Apr 2024
Abstract
This study endeavors to employ a balanced design methodology, aiming to equilibrate the resistance to rutting and cracking exhibited by hot in-place recycling asphalt mixtures containing a high dose of reclaimed asphalt pavement (RAP). The primary goal is to ascertain the optimal amount
[...] Read more.
This study endeavors to employ a balanced design methodology, aiming to equilibrate the resistance to rutting and cracking exhibited by hot in-place recycling asphalt mixtures containing a high dose of reclaimed asphalt pavement (RAP). The primary goal is to ascertain the optimal amount of new binder necessary for practical engineering applications, ensuring a balanced rutting and crack resistance performance of recycled asphalt mixtures. The investigation mainly employed wheel-tracking tests and semi-circular bending tests to assess the rutting and cracking performance of recycled asphalt mixtures with a different dose of RAP (in China, it is common to use RAP with 80% and 90% content as additives for preparing hot in-place recycling asphalt mixtures), and varying quantities of new binders (10%, 20%, and 30% of the binder content in the total RAP added). The results indicated that the addition of new binder reduced the resistance to rutting of the recycling asphalt mixtures but improved their resistance to cracking. Furthermore, for the recycling asphalt mixture with 80% RAP content aged for 5 days, the optimal new binder content is 1.52%, while the mixture with 90% RAP content requires 1.23% of new binder. After 10 days of aging, the optimal new binder content for the recycling asphalt mixture with 80% RAP content is 1.55%, while the mixture with 90% RAP content requires 1.28% of new binder.
Full article
(This article belongs to the Special Issue Performance-Related Material Properties of Asphalt Mixture Components (Second Edition))
Open AccessArticle
Improving the Abrasion Resistance of Nodular Cast Iron Castings by Remelting Their Surfaces by Laser Beam
by
Tomasz Wróbel, Andrzej Studnicki, Marcin Stawarz, Czesław Baron, Jan Jezierski, Dariusz Bartocha, Rafał Dojka, Jacek Opiela and Aleksander Lisiecki
Materials 2024, 17(9), 2095; https://doi.org/10.3390/ma17092095 - 29 Apr 2024
Abstract
This paper presents the results of research conducted in the field of the technology of surface hardening of castings from unalloyed and low-alloy nodular cast iron using the laser remelting method. The range of studies included macro- and microhardness measurements using Rockwell and
[...] Read more.
This paper presents the results of research conducted in the field of the technology of surface hardening of castings from unalloyed and low-alloy nodular cast iron using the laser remelting method. The range of studies included macro- and microhardness measurements using Rockwell and Vickers methods as well as metallographic microscopic examinations using a scanning electron microscope. Moreover, abrasive wear resistance tests were performed using the pin-on-disk method in the friction pair of nodular cast iron—SiC abrasive paper and the reciprocating method in the friction pair of nodular cast iron—unalloyed steel. Analysis of the test results shows that the casting surface layer remelting by laser for unalloyed nodular cast iron results in a greater improvement in its resistance to abrasive wear in the metal–mineral system, as compared to low-alloy cast iron. Additionally, carrying out the laser hardening treatment of the surface layer made of the tested grades of nodular cast iron is justified only if the tribological system of the cooperating working parts and allowable dimensional changes during their operation are known.
Full article
(This article belongs to the Special Issue Research and Development in the World Foundry Engineering: Materials, Properties and Applications)
Open AccessArticle
Tensile Strength and Mode I Fracture Toughness of Polymer Concretes Enhanced with Glass Fibers and Metal Chips
by
Mazaher Salamat-Talab, Ali Zeinolabedin-Beygi, Faraz Soltani, Alireza Akhavan-Safar, Ricardo J. C. Carbas and Lucas F. M. da Silva
Materials 2024, 17(9), 2094; https://doi.org/10.3390/ma17092094 - 29 Apr 2024
Abstract
This study experimentally investigates the influence of metal chips and glass fibers on the mode I fracture toughness, energy absorption, and tensile strength of polymer concretes (PCs) manufactured by waste aggregates. A substantial portion of the materials employed in manufacturing and enhancing the
[...] Read more.
This study experimentally investigates the influence of metal chips and glass fibers on the mode I fracture toughness, energy absorption, and tensile strength of polymer concretes (PCs) manufactured by waste aggregates. A substantial portion of the materials employed in manufacturing and enhancing the tested polymer concrete are sourced from waste material. To achieve this, semi-circular bend (SCB) samples were fabricated, both with and without a central crack, to analyze the strength and fracture behavior of the composite specimens. The specimens incorporated varying weight percentages comprising 50 wt% coarse mineral aggregate, 25 wt% fine mineral aggregate, and 25 wt% epoxy resin. Metal chips and glass fibers were introduced at 2, 4, and 8 wt% of the PC material to enhance its mechanical response. Subsequently, the specimens underwent 3-point bending tests to obtain tensile strength, mode I fracture toughness, and energy absorption up to failure. The findings revealed that adding 4% brass chips along with 4% glass fibers significantly enhanced energy absorption (by a factor of 3.8). However, using 4% glass fibers alone improved it even more (by a factor of 10.5). According to the results, glass fibers have a greater impact than brass chips. Introducing 8% glass fibers enhanced the fracture energy by 92%. However, in unfilled samples, aggregate fracture and separation hindered crack propagation, and filled samples presented added barriers, resulting in multiple-site cracking.
Full article
(This article belongs to the Special Issue Green and Sustainable Infrastructure Construction Materials (2nd Edition))
Open AccessArticle
Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites
by
Waqas Farid, Hailin Li, Zhengyu Wang, Huijie Cui, Charlie Kong and Hailiang Yu
Materials 2024, 17(9), 2093; https://doi.org/10.3390/ma17092093 - 29 Apr 2024
Abstract
This study investigates the mechanical properties of titanium carbide/aluminum metal matrix composites (AMMCs) using both experimental and computational methods. Through accumulative roll bonding (ARB) and cryorolling (CR) processes, AA1050 alloy surfaces were reinforced with TiCp particles to create the Al–TiCp composite. The experimental
[...] Read more.
This study investigates the mechanical properties of titanium carbide/aluminum metal matrix composites (AMMCs) using both experimental and computational methods. Through accumulative roll bonding (ARB) and cryorolling (CR) processes, AA1050 alloy surfaces were reinforced with TiCp particles to create the Al–TiCp composite. The experimental analysis shows significant improvements in tensile strength, yield strength, elastic modulus, and hardness. The finite element analysis (FEA) simulations, particularly the microstructural modeling of RVE−1 (the experimental case model), align closely with the experimental results observed through scanning electron microscopy (SEM). This validation underscores the accuracy of the computational models in predicting the mechanical behavior under identical experimental conditions. The simulated elastic modulus deviates by 5.49% from the experimental value, while the tensile strength shows a 6.81% difference. Additionally, the simulated yield strength indicates a 2.85% deviation. The simulation data provide insights into the microstructural behavior, stress distribution, and particle–matrix interactions, facilitating the design optimization for enhanced performance. The study also explores the influence of particle shapes and sizes through Representative Volume Element (RVE) models, highlighting nuanced effects on stress–strain behavior. The microstructural evolution is examined via transmission electron microscopy (TEM), revealing insights regarding grain refinement. These findings demonstrate the potential of Al–TiCp composites for lightweight applications.
Full article
(This article belongs to the Special Issue Advances in High-Performance Non-ferrous Materials—2nd Volume)
Journal Menu
► ▼ Journal Menu-
- Materials Home
- Aims & Scope
- Editorial Board
- Reviewer Board
- Topical Advisory Panel
- Instructions for Authors
- Special Issues
- Topics
- Sections & Collections
- Article Processing Charge
- Indexing & Archiving
- Editor’s Choice Articles
- Most Cited & Viewed
- Journal Statistics
- Journal History
- Journal Awards
- Society Collaborations
- Conferences
- Editorial Office
Journal Browser
► ▼ Journal BrowserHighly Accessed Articles
Latest Books
E-Mail Alert
News
Topics
Topic in
Applied Sciences, Energies, Materials, Nanoenergy Advances, Nanomaterials
Applications of Nanomaterials in Energy Systems, 2nd Volume
Topic Editors: Eleftheria C. Pyrgioti, Ioannis F. Gonos, Diaa-Eldin A. MansourDeadline: 30 April 2024
Topic in
Buildings, Infrastructures, Materials, Smart Cities, Sustainability
Smart Material and Smart Construction Technologies for Urban Development
Topic Editors: Sathees Nava, Kate NguyenDeadline: 14 May 2024
Topic in
Energies, Materials, Processes, Solar, Sustainability
Solar Thermal Energy and Photovoltaic Systems, 2nd Volume
Topic Editors: Pedro Dinis Gaspar, Pedro Dinho da Silva, Luís C. PiresDeadline: 31 May 2024
Topic in
Bioengineering, JMMP, Materials, Micromachines, Polymers
Advances in Filament Engineering for Biomaterials
Topic Editors: Ming-Wei Chang, Zeeshan Ahmad, Hui-Min David WangDeadline: 30 June 2024
Conferences
Special Issues
Special Issue in
Materials
Synthetic and Biologic Materials for Prosthetic and Reconstructive Applications for Musculoskeletal Tissue
Guest Editors: Dante Dallari, Marco GovoniDeadline: 10 May 2024
Special Issue in
Materials
Advanced Electronic Packaging Technology: From Hard to Soft
Guest Editors: Yue Gu, Yongjun HuoDeadline: 20 May 2024
Special Issue in
Materials
Synthesis, Applications and Characterization of Advanced Precious Metal Materials
Guest Editor: Shaohong LiuDeadline: 31 May 2024
Special Issue in
Materials
Structural Health Monitoring of Polymer Composites
Guest Editors: Patricia Krawczak, Salim ChakiDeadline: 10 June 2024
Topical Collections
Topical Collection in
Materials
3D Printing in Medicine and Biomedical Engineering
Collection Editor: Filip Górski
Topical Collection in
Materials
Catalysts: Preparation, Catalytic Performance and Catalytic Reaction
Collection Editors: Gina Pecchi, Cristian H. Campos
Topical Collection in
Materials
Microstructure and Corrosion Behavior of Advanced Alloys
Collection Editor: Marián Palcut
Topical Collection in
Materials
Manufacturing Engineering and Mechanical Properties of Composite Materials
Collection Editor: Aminul Islam